The difference between a $300 pipe repair and a $3,000 drywall-and-remediation job is often just whether the leak was found before or after excessive wall opening. Our detection service in Sargent uses the same methods utilities and insurance adjusters rely on โ to pinpoint the failure before anything is cut.

No single detection method works for every leak scenario. Our techs are trained on four distinct approaches and select the right tool โ or combination โ based on pipe type, building construction, and leak characteristics.
Most effective on metal pipe under slab or in concrete โ materials that conduct sound efficiently. We establish a clean acoustic baseline by briefly shutting off the house before scanning.
Particularly effective inside insulated wall cavities and for finding the extent of moisture spread beyond the immediate leak point โ telling us not just where the pipe is failing but how far the moisture has already traveled.
We isolate the supply system, pressurize to operating pressure, and monitor over a timed hold period. Any pressure drop confirms active water loss from the supply side. By isolating zones โ hot side vs. cold side, section by section โ we narrow down which branch is leaking before deploying detection equipment.
For leaks that don't produce sufficient acoustic signature โ very slow leaks, polyethylene pipe, or leaks deep under concrete โ we introduce a nitrogen/hydrogen tracer gas mixture into the isolated pipe and use a calibrated gas detector at the surface to find where the gas escapes. Sensitive to concentrations far below what produces an audible acoustic signal.
Our detection service covers the full property, not just the obvious locations.
Supply lines running under or through the concrete slab fail from corrosion, shifting, or manufacturing defects โ and the leak is invisible from the surface but audible to acoustic equipment. We walk the floor on a grid pattern, map the loudest detection points, and triangulate to a specific floor location, typically within a square foot. Confirmed slab leak location is documented with marked coordinates for the repair crew.

Wall and ceiling leaks are often traced by following a visible stain to its apparent high point โ but visible damage can be several feet from the actual pipe failure due to how water travels down framing members. Thermal imaging reveals the wet zone accurately, and acoustic equipment confirms the pipe location within the wall cavity.
We also perform leak correlation surveys for longer line runs, using two listening points to triangulate the failure location mathematically.
Pool plumbing โ suction and return lines buried between the equipment pad and the shell โ develops leaks at fittings or in the pipe body that show as unexplained water loss. We pressure-test the pool plumbing circuit, isolate return and suction lines separately, and use acoustic detection to find which line and where.

We format detection reports specifically for insurance submission and provide documentation on our detection equipment and methodology to claims adjusters on request.
Commercial water loss from undetected leaks often shows up as elevated utility bills for months before physical evidence appears. We can assess a commercial building's plumbing system for suspected leaks at the property owner's or manager's request.
Here's exactly how a Masters Plumbing Service leak detection call plays out in Sargent, GA.
We start at the meter. All fixtures off, we watch the meter for 10 minutes. Movement confirms active water loss from the supply side. We also check for visible evidence โ stains, soft floors, moisture readings with a moisture meter at suspect wall surfaces.
Zone isolation turns "there's a leak somewhere in the house" into "the leak is on the hot side supply between the water heater and the master bath."
Within the isolated zone, we deploy thermal imaging first โ scanning walls, floors, and ceilings for moisture anomalies. Then acoustic equipment confirms the specific pipe location and narrows it to the tightest possible point. Tracer gas is added if acoustic results aren't conclusive.
You receive a written detection report including pressure test results, detection method summary, leak location relative to fixed reference points, and thermal imagery. If you want us to repair the leak, we quote immediately and can execute same-visit.

High-efficiency home with a slow leak โ about 1.5 gallons per hour. The tech used tracer gas after pressure testing confirmed the loss but acoustic detection couldn't localize it clearly. Gas detection found the escape at a micro-fitting under the slab in the utility corridor. Impressive work for a very difficult leak to find.
Ceiling stain in the living room kept coming back despite two drywall patches. Masters Plumbing Service ran the thermal camera and found the wet zone was traveling from a supply line joint 9 feet away, flowing down a horizontal framing member โ explaining why the patch kept failing. They marked the actual pipe location, we opened 8 inches of wall there, and the repair held. No more stain.
Pool was losing 2 inches per day โ more than evaporation. Masters Plumbing Service pressure-tested the plumbing circuit, isolated the issue to the return line, and ran acoustic detection along the line path to find the failure at a union fitting under the decking. Repair required pulling one deck board instead of the exploratory digging another company had proposed.
Our detection technicians are equipped with acoustic, thermal, and tracer gas tools for the full range of leak scenarios found in Sargent, GA homes and commercial properties.

Masters Plumbing Service's detection team finds hidden leaks in Sargent homes and commercial properties using equipment that eliminates guesswork. The detection appointment pays for itself the moment it prevents one unnecessary wall opening.
๐ Call +1-844-833-0201 Now